Expert Answers about Heartland RV
- Solutions To Add More Clearance For Lippert Ground Control 3.0 Jack Legs
- I don't know what type of brackets were used on your 2022 Heartland RV Torque 5th Wheel but we carry the # LC349975, which can really only be installed at one height since they have lip that butts up against the bottom of the I-Beam.
If clearance is the main issue here then another solution would be to raise the height of the trailer to gain a bit more clearance for the jacks. This can be done by replacing the leaf spring hangers with longer ones, using a correct track system # RR23QX,...
view full answer... - Fit of the LaSalle Bristol CrossBreeze Adjustable Toy Hauler Screen
- Yes, it will fit. The LaSalle Bristol CrossBreeze Adjustable Toy Hauler Screen, # 3441409912PBK is 99-1/8" in width and 93" in height.
view full answer... - How Can I Carry A Fat Tire Bike On Rear Of My 5th Wheel
- I am sure we can something that will work for your 5th wheel, but it will not be the Yakima OnRamp Bike Rack for 2 Electric Bikes - 2" Hitches - Frame Mount, part # Y36FR. I just spent some time with the OnRamp on Thursday. Unfortunately, you will not be able to modify the trays to make them fit a 5" fat tire bike. The only way for that bike to fit is for the tires to ride on the trays, not in them. It is something that I would not recommend.
You could use the Hollywood Racks RV Rider...
view full answer... - Which Over-Under Conversion Kit For 2021 Heartland North Trail 22FBS W/ Tandem 3500 Axles
- An over-under kit is a great option for gaining additional ground clearance to get into your steep driveway since they lift the trailer by the diameter of the axle plus the height of the leaf spring stack.
Since your 2021 Heartland North Trail 29' Model 22FBS has 3500lbs axles you will need the the Dexter Trailer Springs Over-Under Conversion Kit # K71-384-00 as 3500lb axles have a 2-3/8" diameter.
I included a video of the # K71-384-00 for you to take a look at.
view full answer... - Trailer Hitch Receiver For Heartland 5th Wheel
- You'll need to do some measuring, but so long as the frame of your 2011 Heartland Landmark 5th wheel is between 22 inches and 72 inches wide, the hitch you can use is the following:
- Adjustable Width Trailer Hitch Receiver for RVs, 22" to 72" Wide # 13703
view full answer... - How To Determine Fit of the Landing Gear Set RVLG-8000
- I don't have any specs on your 2008 Heartland Cyclone 4012 5th Wheel Trailer but all you need to do to confirm fit of the Landing Gear Set part # RVLG-8000 is measure the outer tube as well as the weld stop spacing on one of the legs. If the outer tube is 29-1/2" long and the distance between the weld stops is 15-1/2" inside to inside or 17-1/2" outside to outside then the above set will work for you.
view full answer... - Cargo Carrier With Ramp For A 2018 Heartland RV Bighorn Fifth Wheel
- Currently the only cargo carriers we carry that come with a ramp are hitch mounted and largest size is the 30x50 Flint Hill Goods Cargo Carrier w/ 48" Ramp # FHG77ZR. If your 2018 Heartland RV Bighorn Fifth Wheel doesn't have a trailer hitch receiver then you could install the Adjustable Width Trailer Hitch Receiver for RVs, 18" to 51" Wide # C13702 if the distance between the frame beams is within the 18" to 51" capacity of this hitch.
If you have a larger frame width then you could use...
view full answer... - Bearing Kit For 2016 Heartland Cyclone 4200
- We have the exact kit you need to replace your bearings, races, and grease seal on your 2016 Heartland Cyclone 4200, which is the following:
- Bearing Kit # BK3-200
This kit is for one hub, so if you need to replace the bearings and seals on multiple hubs, just be sure to order the correct quantity. And then for grease I recommend the LubriMatic Grease # L11380 with Bearing Packer # ALL647646.
view full answer... - How To Send Brake And Turn Signals Through A Travel Trailer To A Boat Trailer
- You would need to wire in a 4-pole connector like # 18004 into the tail lights of your 2020 Heartland Mallard M260 travel trailer to send the signal from the travel trailer to the boat trailer. This will require some additional additional wiring # 16-4B-1 and some heat shrink butt connectors # DW05744-10 for a watertight connection.
Once this is complete you can plug in the 4-pole connector from your boat trailer into your travel trailer.
view full answer... - Length Of The JR Products Sink Strainer # 37295215
- the Sink Strainer w/ Pop-Up Stopper # 37295215 is 5-1/2" tall from the flange down to the end of the drain pipe. You'll want to ensure that the sink has a 1-3/8" to 1-3/4" opening in order for this to fit.
view full answer... - Will The Lippert RV Slide-Out Motor by Klauber # LC130057 Fit a 2009 Heartland North Country?
- Unfortunately, I have no way to look up what parts are installed on your 2009 Heartland North Country. You may be able to contact the RV manufacturer with your VIN number to determine if they kept record of this when they manufactured the RV. Otherwise I would need for you to remove your current slide out motor and send me the information off the motor itself. I would then be able to cross reference the information to determine if the Lippert Motor # LC130057 will fit.
view full answer... - 9/16 Inch Lug Nuts and Drive-In Trailer Hub Studs
- For 9/16" lug nuts we have the Trailer Wheel Lug Nut - 9/16" # 6-53.
Then, for drive-in 9/16" wheel studs, which are 2-1/2" long, the correct part is the Trailer Hub Wheel Stud # 7-257.
These are sold individually so you'll want to make sure you order the appropriate amount for your hub and wheels.
view full answer... - Is Solera 20 Foot Replacement Awning Fabric LCV000334437 Correct For 20 Foot Center to Center Fabric
- Since your Solera power awning measures 20 feet from the center of the left arm to the center of the right arm, you do have the correct replacement fabric:
- Solera 20' Replacement Awning Fabric - Sand Fade w/ Black Weatherstrip # LCV000334437
I did verify with Lippert that this replacement fabric has a single polycord.
view full answer... - What Does AT93312 Harness Connect To
- I can't find anything regarding a water heater number 62659 or MPD 91818, and you'll have to know your water heater's model number. The Replacement 4-Wire Control Harness # AT93312 connects to the Control Panel # AT91367, and the pair fits Atwood water heater models G6A-2E, G6A-6E, G6A-7E, G6A-8E, GH6-3E, GH6-6E, GH6-7E, GH6-8E, G10-1E, G10-2E, G10-3E, GH10-1E, G10-3E, GC6A-7E, GCH6-4E, GCH6-6E, and GCH6-7E.
view full answer... - Replacement AC Unit Options For A 2016 Heartland RV Oakmont 5th Wheel With Dometic AC's
- While we don't currently offer Dometic branded AC units I do still have a solution for you with our Furrion AC units. You'll first want to remove the cover of your air distribution boxes and see if the wire harness that hangs down from your Dometic rooftop unit has a 6-pin or 9-pin connector. If you're just wanting to replace only the rooftop unit and retain use of the air distribution boxes and thermostats that you have then you can use the following units depending on the style connector...
view full answer... - SnapPads For a 2019 Heartland Mallard M32 Travel Trailer With Lippert Stabilizer Jacks
- I was able to narrow down your 2019 Heartland Mallard M32 to having the Lippert stabilizer jacks. They will be either the 5-1/2" to 5-5/8" Pads # SN68FR or the 5-3/4" to 6" Pads # SN99FR. You will need to measure your stabilizer feet to find the exact pads.
view full answer... - How To Choose the Correct Replacement Electric RV Stabilizer Jack Motor
- There are two replacement motors for the electric stabilizer jacks, Replacement Electric RV Stabilizer Jack Motor part # LC138445 and Replacement Electric RV Stabilizer Jack Motor part # LC352338. In order to choose the correct replacement motor you simply need to note the color of the support arms. If you support are yellow then you need the Replacement Electric RV Stabilizer Jack Motor part # LC352338 but if the support arms are black then you need Replacement Electric RV Stabilizer Jack...
view full answer... - Could 4,400 lb Trailer Hub Fit 2017 Heartland Trailrunner 30USBH
- I don't have a way to verify the axle you have on your 2017 Heartland Trailrunner 30USBH but if you know you have a 4,400 lb capacity axle the hub part # 8-407-5UC3-EZ is a confirmed fit and comes with everything needed to install as far as bearing and seal are concerned. It also comes with new lug nuts.
You might need grease though as this is not pre-greased. For that the LMX red grease like part # L11390 is a great option as it's waterproof and the most heavy duty grease out there.
view full answer... - Fit of Roadmaster RM-2460-2570-3 Comfort Ride Suspension on Heartland Cyclone Triple Axle Toy Hauler
- Which model Heartland Triple Axle Cyclone 5th Wheel toy hauler do you have?
The Roadmaster # RM-2460-2570-3 Comfort Ride Leaf Spring Suspension Kit w/ Shock Absorbers will work if your toy hauler has 7K axles. There isn't a database that would allow me to look up which axles your toy hauler is equipped with, but there are a few things to look for that will confirm your axle capacity. A 7K axle typically uses a 3 inch diameter axle tube with spindles that use a 25580 inner and 14125A outer...
view full answer... - Is The MaxxAir MaxxFan Remote Compatible With Deluxe Series Fans?
- Yes, the Handheld Remote # MA00A01150K will work on the MaxxFan Deluxe series of roof vents. Your fan must have been a model compatible with the remote as some of the manual fans do not have the correct circuit board or touchpad to work with the remote. If you can tell me exactly which model fan you have I can verify compatibility. The paperwork for the different models is the same but you will need to identify your exact fan.
view full answer...
Go To Results